How to Attach Kitchen Cabinets to The Wall Like a Pro

Are you thinking of installing kitchen cabinets? Our step by step instructions will guide you through the entire process. Kitchen cabinets are an excellent way to add extra storage place for items and decors in a space. They come in various shapes and sizes for both functionality and aesthetic appeal. These cabinets are usually heavy and further supports the additional weight of the items stored. Therefore, it is very crucial to properly hang them through builder standard methods.

The principles and methods of installing cabinets are relatively the same. You don’t need any special skills as long as you can follow the manufacturer’s instructions well. For a Do It Yourself  cabinet project, ensure that you have all the necessary tools and supplies. You will also need a strong helper to help with the heavy lifting of the cabinets. Here is a guide on how to attach kitchen cabinets to the wall like a pro.

Preparation of Cabinet Installation

If you are installing cabinets in a new house, it is advisable to do so after the completion of plumbing and rough wiring. However, hang the cabinets before the installation of the finish flooring to avoid the risk of damage.

When you are remodeling your kitchen, ensure that you don’t damage the walls while removing the old cabinets. For this, it is best to take off drawers, shelves, and doors before you unscrew the nails or screws. Check the walls for any voids and bumps that will require fitting by placing a long straightedge against it.

Plan your space to know exactly where you will hang the cabinets. An important tip is to install the wall cabinets first. This helps to prevent the base cabinets from getting in your way during lifting and fastening.

Go ahead and unpack the cabinets. Ensure that all the parts are included and assemble the cabinets through the owner’s manual if it came disassembled. Label all the parts and don’t add the shelves, doors, and drawers until the unit is installed.

Measure and Mark the Wall

Proper installation begins with a good layout. First, consider the height of the base cabinets. While most standard cabinets measure 3-1/2 inches high, you need toad extra 1-1/2inch for the countertop. Furthermore, the usual backlash requires 18 inches. Mark a horizontal line on the wall using a level. The total measurement should be 54 inches from the floor. Measure this line down to the floor in different areas and mark using chalk. Ensure to include the highest point of the floor in your markings if the floor is not level.

Locate the wall studs with the help of a stud finder. The wall studs will provide the cabinets with firm support. Pay special attention to the plumbing and electrical wiring.

Secure The Ledger Board

position the support board to the wall and secure it into the studs that you marked earlier. They go a long way in supporting the weight of the cabinets during installation. Furthermore, the ledger ensures the straight alignment of the unit.

Hang The Cabinets

there are two options that you can use in this place. You can either attach two cabinets at a time before installing them on a ledger. Or fitting the cabinets one at a time. Make use of the clamps to keep the cabinet frames together and level. Drill the screws where the separate units meet on the top, bottom, front, and back. Once on the ledger, shim the cabinets if it is essential.

Next, attach cabinets to the wall by drilling screws through the framing on the top and bottom of the units. Repeat the whole process for the remaining cabinets. Use a filler bar  to close the gap between the last cabinet and the wall if there is any space.

Once the cabinets are securely attached on the walls, put in the drawers, shelves, doors, and any other hardware. You can remove the ledger if you are done installing the cabinets.

Base Cabinets

In case your floor is not level, start by installing the first cabinet at close proximity to the high point. Use the stud finder and locate the wall studs along the horizontal line you made earlier. Fit the unit in place and ensure that it is level. Shim if necessary to level it.

Next, predrill the framing into the marked studs and then tighten with screws. Check again to ensure that it is level. Repeat the entire process until all the kitchen cabinets are attached to the wall. Proceed and put the hardware in place.


Following these simple tips will facilitate a neat and tidy job. Not only does it provide a professional finish, but it also guarantees the strength and safety of the unit. Try it and enjoy your new home look!